Energi Savr Node for EcoSystem
The Energi Savr Node unit is a DIN-rail mounted Eco Link controller for EcoSystem ballasts, drivers and devices. It provides Eco Link power and control for two independent Eco Links with up to 64 ballasts each. The Energi Savr Node unit also provide direct connections and power for the following Lutron devices:
• Occupancy sensors
•Daylight sensors
•IR receivers
•QS devices
Features
• Provides EcoSystem Link power for either one or two links of EcoSystem ballasts or drivers (up to 250 mA per link).
• Power failure memory retains control unit program ming in the event of a power loss.
• Default configuration requires no commissioning.
• Four occupancy sensor inputs for automated control of lights in areas.
• Four daylight sensor inputs automatically adjust light levels based on the amount of natural light entering through the windows.
• Four IR receiver inputs for personal control or compatible Lutron IR wallstation controls.
• Add more occupancy sensors, daylight sensors, or IR receivers by connecting QS Sensor Modules (QSMs).
• Includes QS link for seamless integration of lights, motorized window treatments, control stations, andQS Sensor Modules.
• Energi Savr Node units and QS Sensor Modules can be used in a Quantum system to control and manage light in an entire building.
Power
• 230 V ~ 50/60 Hz, 100 mA
• Lightning strike protection meets ANSI/IEEE standard 62.31-1980. Can withstand voltage surges of up to 6 000 V ~ and current surges of up to 3 000 A.
• Eco Link Output: 18 V 250 mA maximum per Link.
Standards
• IEC 60669-2-1
• Lutron Quality Systems registered to ISO 9001.2008.
Environment
• Ambient Temperature Operating Range: 0 ?C to 40 ?C.
• Relative humidity: less than 90% non-condensing.
• For indoor use only. Terminals
• Mains wiring: 1,0 mm2 to 4,0 mm2
• Eco Link Wiring: 1,0 mm2 to 4,0 mm2
• QS Link Wiring: 0,5 mm2 to 4,0 mm2
• Input Wiring: 0,5 mm2 to 2,5 mm2
Mounting
• Intended to mount within an IP20 (minimum) rated
consumer panel or breaker panel with integrated
DIN rail and dead cover
• Width = 9 DIN modules (161,7 mm).
Programming Requirements
• An Apple iPod touch or iPhone
mobile digital device with the Energi Savr app is required for programming Energi Savr Node
systems.
• The Energi Savr app is available from the AppStore online store.
• The Energi Savr app cannot be used to program the Energi Savr Node units when installed as part of a Quantum system.
• The Apple iPod touch or iPhone communicates with the Energi Savr Node unit via a WiFi router (not included).
• See “Wiring: System Programming Connection” section for further information.
EcoSystem
• Control up to 64 EcoSystem - compatible devices (ballast,modules, or LED drivers) per EcoSystemDigital Link (up to 128 devices per Energi Savr Node with EcoSystem unit): — EcoSystem ballasts and modules — EcoSystem H-Series ballasts
— Hi-lume 3D ballasts
— Hi-lume LED drivers
— Hi-lume A-Series LED drivers
• Digitally define areas and zones.
• Configure wired or wireless sensors and controls to control devices on multiple EcoSystem Digital Links and/or multiple Energi Savr Node units.
• Automatic replacement of a single failed ballast, module, or driver.
• Simple method of replacing multiple failed ballasts, modules, or drivers.
• EcoSystemDigital Link can be wired as Mains voltage or IEC PELV for maximum wiring flexibility.
QS Link Limits
• A QS link can have up to 100 zones (outputs), 100 devices and 512 ballasts.
• Each Energi Savr Node unit counts as one device toward the 100 device limit.
• Each assigned zone counts toward the 100 zone limit (up to 512 zones in a Quantum system).
• Each Energi Savr NodeT (QSNE-2ECO-D) unit can supply 3 power draw units. Refer to the QS Link Power Draw Units specification submittal (Lutron P/N 369405) for more information concerning Power Draw Units.
• A maximum of 8 EcoSystem digital links may be connected to the QS link.
QS Link Sensor Limits:
• 100 wired or wireless occupancy sensors.
• 100 wired or wireless daylight sensors.
• 100 wired wallstations or Pico wireless controllers.
